sync4

126/361

Wall surfaceWall surfaceHghPower Spotlight・When illuminance level is 0〜2500lx・When installed in such a way that direct sunlight, windows, blinds, etc. do not enter the detection range.GLARE-LESSGENERAL DOWNLGHTSPOTLGHTII I II I II i ilIi liILNEAR32 PENDANTBaseLghtDESGNBASELGHTStripLghtMu-ModueSpotli LNEAR17/32LNEARLGHTghtFoodghtOUTDOORSPOTLGHTli Lnear SpotlightUnder eaves for DOWNLGHT2m3m5m(a)Wall surfaceWired signal (CPEV-1P/0.9)Wired control typelighting fixtureWired control typelighting fixtureWired control typelighting fixtureWired signal (CPEV-1P/0.9)Wired control typelighting fixtureWired control typelighting fixtureWired control typelighting fixture0m1m2m3m4m5mDetection result of ambient temperature 25℃ environmentUnit: m(sensitivity 6)5m7.07.5Ceiling heightDirection (a)Direction (b)2m3.54.03m4.05.0Detection result of ambient temperature 30℃ environment(sensitivity 6)(b)Ceiling heightDirection (a)Direction (b)2m3.03.0*Ceiling height up to 5m3m3.54.5TerminatingresistorTerminatingresistor0m1m2m3m4m5mShading sealSensor partPhotocell/motionsensorDetection areaShading sealSensor partPhotocell/motionsensorDetection area(24-hour power supply)(24-hour power supply)Longitudinal direction of themotion sensor detection rangePhotocell/motion sensor2.0m1.5m3.0m5m1.0m1.5m5m5.05.0Wall surfaceIlluminance sensor functionBrightness sensor functionDetection/installation rangeDetection/installation range[Fig. 1] Lighting fixtures with wireless module that enables direct communication of photocell/motion sensor Lighting fixtures with wireless modules that cannot directly communicate with photocell/motion sensorBrightness sensor functionMotion sensor function65°30°Motion sensor functionPrecautions for use*Sensitivity is automatically adjusted when calibration is performed.45°4m diameter4m diameter4m diameter5.6m diameter5.6m diameter5.6m diameter10m diameter10m diameter10m diameterPWM dimmerPWM signal(CPEV-1P/0.9)For dimmingFor tuningSensor sensitivity7 levels adjustableIlluminance sensor functionFactory setting: ( Level 4 )Motionsensor function15 levels adjustableFactory setting: ( Level 6 )Refer to the user's manual for Smart LEDZ Fit/Fit Plus for detailed information about the various functions.Detectable illuminanceDetection locationCenter of lighting fixture group*Ceiling height up to 5m*Limit the detection range with a light shielding sticker, when installing near direct sunlight, reflected light, windows, and blinds.*Wired signals have polarity.*Do not branch wiring for wired signals other than lighting fixtures.Smart LEDZWireless signalWired repeaterACWired repeaterACTwo types of functions can be selected with one smart sensor switch. It is recommended to install this product within a line-of-sight distance of 25m from the gateway panel or gateway switch.*If it is difficult to install within a line-of-sight distance of 25m, it can be installed within 3 hops, but the farther away from the gateway panel/gateway switch, the slower the reaction speed.Refer to the user manual of Smart LEDZ Base for detailed information of each function.The lighting fixtures connected to the wired repeater will have the same dimming and toning. Also, it is not possible to connect dimming, tunable, and synca to a single wired repeater at the same time.Tuning range at PWM signal input (Tunable: 2700K to 6500/Synca: 1800K to 12000K)* Color rendering of 121 colors and Duv control are not possible.Contact to the sales office for the details of Smart LEDZ fixtureTwo types of functions can be selected with one photocell/motion sensor. Install at least one lighting fixture with wireless module controlled by this product within the radius of 25m (diametrical 50m) from this product.(Refer to [Fig. 1])Detectable illuminance: 0 to 2500 lx (reference) Detectable distance: Max 5m*Since the product is installed on a wall, the illuminance value is used as a guide.*Up to one unit can be registered in one room when using the brightness sensor function.*Since this product is a wall-mounted type, be careful not to allow direct sunlight, mirrors, windows, blinds, etc. to enter the detection range.*Be sure to set the brightness sensor after installing fixtures.Detection condition・0〜4000lx・Install the product away from direct sunlight and reflected light, windows, and blinds. If it is impossible to install the unit at a distance, attach a light-shielding seal.・Do not expose the sensor to direct light.Conditions for detection of motion detection sensor: When both ① and ② are satisfied① The temperature difference with the surroundings is 4°C or more.② Moving speed is 0.3 to 2.0m/s0~4000lxTop viewSide view120°5mMotion sensor functionThe motion sensor detection rangehas directionality.Check the direction of the detection range marking when installing.Detectable distance: Max 5m*Up to six units can be registered in one room when using the motion sensor function.[Fig. 2]In the case of one side light shieldingIn the case of both sides light shieldingSide view6°5m40°126Photocell / motion sensor (FX-428WA/BA)Smart sensor switch (FX-499W/H)Wired repeater (FX-508W)25m radius・The motion sensor detects under two conditions: a heat source using an infrared sensor (temperature difference from the surroundings is 4°C or more) and the operation of that heat source (movement speed).Areas where the skin is not covered by clothing, such as the face and hands, are common detection points.*Ceiling height up to 5m・If there is a heat source or temperature difference within the detection range of the motion sensor, it may cause false detection. For details, please refer to "5. How to determine the control range" in the instruction manual.Detection conditionWhen the human body is at normal temperature and the moving speed is 0.3~2.0m/sTop view150°